Tag Archives: water heater maintenance tips

How To Flush & Drain a Hot Water Heater | Maintenance Tips | The Home Depot

[MUSIC PLAYING] All proper, Ivan. I heard that you have somequestions about your water heater, and preventativemaintenance, and how we will prevent some money at present. A woman neighbor told me that youneed to do preservation as soon as a year, and that i used to be thoroughly clueless about it. I fully grasp that, and i’m going toshow you a couple of hints and tips about what you can do to extendthe life of this computing device, and how that’s going to avoid wasting you cash.I see that you’ve agas, now not an electrical unit. All right. So if it was once electric, we wouldbe watching for the breaker, so one can flip off theelectrical vigour to the burner. Good enough. However it is fuel, so I needyou to grab that ladder, and get it there, andturn off that fuel valve. All correct. You are just going to turn thatto perpendicular with the pipe. And that right thereit’s going to show off your fuel, which is feeding yourburner down on the backside of the tank.It’s going to be yourvalve proper over right here. You are going to close that valve for us. And what we’re goingto do is we will discontinue the give of waterthat’s filling the tank correct now. Let’s take a seem at thepressure free up valve. All correct. The strain unencumber valve isdesigned to fail before the tank does. So right now, what is going on onin here is a number of sizzling water, a lot of high temperatures,numerous high pressure. If it gets too high,this valve will unlock, so it doesn’t harm your tank.Good enough? And that i see that you just havean extension pipe going for walks right down to the backside about sixinches off the ground, which is ideal in view that protection first. If this valve was up right here,quality and excessive, and it failed, you’d have the talents danger ofbeing burned via scalding hot water. So let’s get a bucket. We’re going to put it underneath right here,and we’ll release the valve and distribute a couple cups of water. Satisfactory. Once you received it beneath there,you are going to come again up prime and elevate that silver handle. Just gently pull it up. And we’ll getsome water flowing. All right. That you could let it go. As soon as it stops jogging, we’re going toknow that the valve’s in excellent form. If it does no longer discontinue, then weknow the valve has failed, and we will be able to have got to replace it. It can be very effectively and easilyreplaced via utilizing a pipe wrench. Once you get it outand get the brand new one in, you’ll want to observe some Teflontape to the threads on the brand new valve.And apply that tape clockwise,so as you thread it down, you’re going to quite seal up theunion between the valve and the tank to prevent any leaks one day. Now that we have now validated ourpressure liberate valve, we’re without a doubt going to empty the tankand get any sediment out of it that can have accumulated. So does the tank have sediment? Well, within the water, youhave dirt, you bought minerals, and deposits that are without a doubt going tosettle down to the backside of the tank.And that is going to motive corrosion andrust on the within liner of your water heater. So once a year, you wantto hook up a backyard hose and drain that tank to get any sedimentthat will have collected out of there. Perfect. All right. It’ll extendthe life of your unit. So let’s simply take hold of a garden hose. Let’s get it connected,and we will run it outside to your closest drain. And let’s empty this tank out andget any sediment out of there. All correct, Ivan.Now that we’ve gotten thatgarden hose run outside, let’s get this hose threadedonto that drain valve. And we’re to open up ourpressure unlock valve. Leaving this open isgoing to avert a vacuum. So this manner, we get a good strongflow of water out of this method. All correct, appears clear. Nice. All correct, let’s get again inside. One last thing I wantedto talk about used to be the anode rod, or the sacrificial rod. Now considering that water involves loads ofparticles, like chlorine, fluoride, and magnesium, thoseparticles will certainly corrode the within of your tank. So the sacrificialrod, the anode rod, is fabricated from traditionally aluminum ormagnesium and will truely attract these particles to it. So it’s going to prolong the life of your tank. But clearly, it can be sacrificingitself, so it’ll have to be replaced. Now these rods arefactory established, so i would recommend getting a professionalplumber to come out and clearly cast off it and substitute it for you. Now that now we have gotten all of the gunkout and carried out our maintenance, let’s get the valves openedup and get it up and walking.Perfect. All right? First things first, we’re going to startby refilling the tank with our water waft valves. You always want to makesure you replenish your tank before you flip in your heating aspect. Otherwise, you’ll finish upburning out your heating aspect. A whole other repair. Water valve’s open. Let’s activate that fuel valve again. All proper, gas valve’s open. Let’s ignite that pilot gentle andget some warmth again within the tank. Best. So now, the common householdis going to set its temperature to 120 levels on this water heater. But somewhat vigor saver tip. Each 10 degrees youlower your temperature, you’re going to retailer 5% off on theoperating fee of this water heater. Quality. Saving money. All correct. Thanks a lot for coming. No difficulty. Thank you. And thanks forshopping at house Depot.

Water Heater – Maintenance Guide | Repair and Replace

Hi, I’m Vance and welcome to Repair and Replace. If you want to extend the life of your waterheater then regular maintenanceshould be done once a year. This will also give you a sense of any futureproblems before they arise. In this episode we’ll go over how to properlymaintain your standing pilot water heater. First we’ll look for leaks and then we’llcheck the airflow. Next we’ll test the pressure and temperaturerelief valve, then check the anode rodto see how corroded it is. Finally we’ll drain and flush the tank toremove the sediment. Let’s begin. Before you get started, you’ll need a gardenhose, a bucket, a 1 & 1/16th inch socket, a half inch drive socket wrench, a breakerbar, a screwdriver, needle nose pliers, a wire brush, teflon tape,and a multi-use cleaning brush.First turn the gas supply off, or perpendicularto the pipe. Now set the water heater to the pilot setting,and turn the gas control off. Next shut off the cold supply. Keep in mind that the water inside the tankis still hot, so use caution when draining or accessingthe tank. To start, it’s best to do a walk around tocheck for any leaks. Check the inlet and outlet pipes leading intothe tank. Next check the pressure and temperature reliefvalve, looking for any water weeping around the threadsor around the valve body. Now look at the drain valve. If you see any water leaking it’s bestto replace that part. You can see how to replace the pressure andtemperature relief valve as well as the drain valve in the videos linkedbelow. If you have a standing pilot water heater, it’simportant to check that there is good airflow. On the bottom of the tank, air is broughtin through a flame arrestor screen, which can get cloggedwith dust or debris.This can create backdrafting, which can causethe pilot to blow out. Anything can be used to clean the screen,but this is easily done with a multi-use brush, such as one used toclean the bottom of refrigerators. Now check the flue vent, and clean out anydust around it. The temperature and pressurerelief valve is by far the most important safety devicein water heaters. If the pressure or temperature inside thetank gets too high, the valve will open and release water, preventing the tankfrom exploding. It’s important to test the valve to be surethat the valve can open when needed. Place a bucket below the drain tube and liftthe lever to drain several gallons of water. Now close the valve. The water should stop flowing completely. Now if the relief valve doesn’t close, andyou still have a little bit of water flowing, then you’ll have to replacethe valve. And you can see how to do this in the videolinked below. First, open a hot water faucet in the house. This will let in air and relieve pressurein the system. Place a bucket underneath the drain valve.Open the valve to drain several gallons ofwater, this will reduce the pressure in the tank. Ideally you want to leave mostof the water in the tank as the weight will keep the tankfrom sliding around. The anode rod is sometimes under a plasticcover, this will usually just pop off. If you haven’t checked it in years, it mightbe stuck in place, and will be difficult to remove.To prevent the tank from shifting, you canuse a piece of wood to stabilize the tank. Alternatively, you can get another personto help support it. To get it started, you’ll need to increasethe torque. One way is to use a breaker bar. Additionally you can use a copper pipe asan extension or snipe. Once the nut is starting to spin, then youshould be able to use a regular socket wrench tounscrew it.Now use the needle nose pliers remove theanode rod. Each year that you check the anode, take noteof what has changed. Most anodes will last 4-6 years, but thisdepends on the pH and purity of the water. If you can see the bare steel core or if therod is completely encased with calcium, then the anode will have to be replaced. To get a good seal, its best to clean outthe threads with a wire brush. Next apply the teflon tape.This will help seal the threads and make iteasier to remove and check the rod. Looking at the threads, tape is always appliedin clockwise direction, so that the tape stays on when tightened. Wrap 3-6 times, keeping it tight the wholeway through. Leave the last part of the thread bare, to prevent any tape frombreaking off into the tank. Now screw the nut into placeuntil it is hand tight. Finally use the socket totighten it into place. To do a deep flush of your tank, you’ll haveto drain all the water. First, connect the garden hose to the drainvalve. Open the valve to drain the water. This process can be slow and might take 30minutes or more to drain. Now that the tank is empty you can do a flushto remove some of the built up sediment.Turn on the cold supply for 20 seconds toblast water into the bottom of the tank. This will agitate and lift the sediment. Now drain the water. You can repeat this 4 or 5 times as needed until the water draining out ofthe hose is running clear. Now open the cold water supplyto fill the tank. Check the faucet, you should hear the airbeing pushed out of the system. Close the faucet once you get a smooth streamof water.This will tell you that the tank is full,and the air has been removed. If you have an electric water heater, turnon the power at the breaker. For gas water heaters, turn on the gas, andrelight the pilot. To see how to relight the pilot, watch thevideo linked below. Now that you know how to properly maintainyour water heater, it will be easy to keep it running smoothly. For more troubleshooting on water heaters, furnaces and appliances,then subscribe to our channel.And if you need help, you can call or visitan AMRE location to talk with our knowledgeable staff. Thanks for watching..